单级跨声速压气机进气畸变数值模拟

基于彻体力模型的基本思想,发展了一套能够反映进气畸变对风扇/压气机气动性能影响的三维数值计算程序CSAC.首先详细研究了彻体力模型的具体建模方法,然后发展了相应的三维数值计算程序.利用该程序针对某单级跨声速压气机在均匀进气下的流场进行了计算验证,计算结果与雷诺平均Navier-Stokes(RANS)计算吻合得很好,流场主要参数分布与相关实验数据也有很好的一致性.利用该程序分别计算分析了进口存在稳态周向总压畸变及周向总温畸变的全环三维畸变流场,结果表明:压气机进口畸变流场存在大尺度、强三维特征,将导致压气机总压比及稳定裕度下降.所有计算结果均显示该模型能够在降低对计算资源和工程经验依赖的同时,有效分析进气畸变对压气机特性的影响.      

基于阶跃响应的飞行器单独静、动导数数值求解方法

基于阶跃响应方法,结合刚性动网格技术,对飞行器的单独静、动导数的精细化数值计算进行了研究.以纵向为例,通过给物面施加恒定附加攻角,求解得到阶跃响应运动过程的非定常气动力,求导得到静导数.同样给物面施加恒定的俯仰角速度,并同时强迫物面平动以抵消俯仰转动产生的附加攻角影响,可由非定常气动力求导得到动导数值.分别利用NACA0012翼型和三维SACCON飞翼无人机进行了计算验证,各攻角下的静、动导数值与文献、试验结果吻合得很好,最大误差不超过5%.结论表明:基于阶跃响应的单独静、动导数直接模拟方法计算耗时仅为传统强迫振动方法的21%,效率相对较高,且可推广到横航向的动导数计算,为飞行器的稳定性研究提供参考.      

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

Effect of sodium tartrate concentrations on morphology and characteristics of anodic oxide film on titanium alloy Ti–10V–2Fe–3Al

The effect of sodium tartrate concentrations on morphology and characteristics of ano-dic oxide film on titanium alloy was investigated. The alloy substrates were anodized in different concentration solutions of sodium tartrate with the addition of PTFE emulsion and their morphol-ogy and characteristics were analyzed. The anodic oxide film presented a uniform petaloid drums and micro-cracks morphology. Additionally, micro-cracks dramatically swelled with the increase of the tartrate concentrations. The thickness of the anodic oxide film increased with the concentra-tions until the concentration reached 15 g/L. The results of Raman analysis illustrate that all sam-ples have similarity in the crystal structure, consisting of mainly amorphous TiO2, some anatase TiO2 and a small amount of rutile TiO2. And the ratios of anatase TiO2 and rutile TiO2 increase with the concentrations until it reaches 15 g/L. Furthermore, the intensity of the peaks increases with enhanced concentrations until the concentration reaches 15 g/L. The corrosion resistance of the anodic oxide film is increased by the sodium tartrate with higher concentrations before 15 g/L. The coefficient of friction of the anodic oxide film reduces with the concentrations until the concentration reaches 15 g/L, then the coefficient of friction of the anodic oxide film increases with the concentrations.     

一种基于蜂拥策略的分布式无人机编队控制方法

在无人机编队控制中,传统的主从式集中编队控制方式需要大量信息交互,对机间通信的要求较高.针对具有虚拟领航者的分布式无人机自组织编队跟踪问题,运用有界蜂拥算法对无人机模型进行求解.首先,提出了一种有界控制输入的蜂拥算法,并对算法的稳定性进行了分析;其次,对无人机进行了建模,提出了虚拟受力点的概念,并对虚拟受力点进行受力分析,将算法中的加速度转化成无人机径向速度与偏航速度的更新,以达到分布式无人机编队自组织以及跟踪虚拟领航者的目的;最后,通过仿真验证了算法和模型的有效性.     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

Multi-Sphere Method for modeling spacecraft electrostatic forces and torques

The use of electrostatic (Coulomb) actuation for formation flying is attractive because non-renewable fuel reserves are not depleted and plume impingement issues are avoided. Prior analytical electrostatic force models used for Coulomb formations assume spherical spacecraft shapes, which include mutual capacitance and induced effects. However, this framework does not capture any orientation-dependent forces or torques on generic spacecraft geometries encountered during very close operations and docking scenarios. The Multi-Sphere Method (MSM) uses a collection of finite spheres to represent a complex shape and analytically approximate the Coulomb interaction with other charged bodies. Finite element analysis software is used as a truth model to determine the optimal sphere locations and radii. The model is robust to varying system parameters such as prescribed voltages and external shape size. Using the MSM, faster-than-realtime electrostatic simulation of six degree of freedom relative spacecraft motion is feasible, which is crucial for the development of robust relative position and orientation control algorithms in local space situational awareness applications. To demonstrate this ability, the rotation of a cylindrical craft in deep space is simulated, while charge control from a neighboring spacecraft is used to de-spin the object. Using a 1 m diameter craft separated by 10 m from a 3 by 1 m cylindrical craft in deep space, a 2 °/s initial rotation rate can be removed from the cylinder within 3 days, using electric potentials up to 30 kV.     

基于力约束的空心涡轮叶片陶芯定位方法

精铸蜡型作为空心涡轮叶片精铸过程重要的前期工艺转接件,其壁厚精度主要由蜡型模具型腔与内部陶芯的位置匹配关系决定。由于陶芯在模具内完全依靠定位元件实现空间定位,为减小由定位误差引起的陶芯位姿漂移,提出了一种基于力平衡约束的空心涡轮叶片精铸模具陶芯定位布局优化方法。首先,通过建立陶芯定位误差传递模型,揭示了定位误差与陶芯空间位姿扰动量之间的映射关系;其次,根据力平衡原理构建了基于力约束的陶芯定位布局优化模型;之后,针对陶芯表面定位候选点的离散分布特性,结合遗传算法给出了陶芯定位布局点的详细求解策略。最后,仿真对比证明了利用本文所提方法获得的陶芯定位方案可以在保证陶芯定位稳定性的同时提高陶芯定位精度,此外,按照优化后的定位方案压制实际蜡型,壁厚检测结果也进一步表明所提方法的有效性。     

数字化组合式大力值校准系统的研制

为了满足对大力值(20 MN左右)的测量和校准,开发了一套数字化组合式大力值校准装置。其最大量程可达24 MN,系统测量准确度为0.1%,适合于大型材料试验机的校准和检定。本文详细介绍了装置的组成结构、弹性体设计、贴片和组桥方式、数字化的方法以及与计算机的通信实现。